ARCHIV

Dobrý den,
mám cca asi půl roku OpenSuse 10.2 na počítači s procesorem AMD Athlon XP 2000+, 1024 MB pamětí, grafikou ATI Radeon 9000 (chystám se nahradit nějakou GForce kartou, v 10.2 už zdá se nerozchodím, pro tuto grafiku oficiální ATI ovladač jako v 10.1 :-( a ten open ovladač mi dost snížil možnosti ... musel jsem dát nižší rozlišení, jinak jsem měl jen 60 Hz a z toho parádně bolely oči). Základní desku mám MSI KT3 Ultra2. V počítači mám 2 disky, jeden 160 GB Seagate rozdělený na dvě NTFS části s Windows a druhý 300 GB Seagate, kde mám na cca 100 GB Linux a zbytek mám udělaný jako oddíl s Ext3 pro sdílení a zálohy mezi oběma OS (na Windows pro to mám nějaký plugin myslím ExtFS, díky kterému tam mám plný přístup). OpenSuse 10.2 se mi moc líbí (nemám s ní tolik problémů jako na 10.1), ale jeden problém mám dost výrazný a mé dosavadní "zatím chabé" znalosti Linuxu na jeho řešení evidentně nestačí. Jako okenní prostředí mám KDE verze 3.5.6 "release 64.1".
Problém se projevuje, když kopíruji nějaké DVD na disk (jako souborový manažer používám Krusader verze 1.70.1), obvyjkle ten Ext3 oddíl (ale zkoušel jsem to i při kopírování do svého Linux home adresáře a výsledek byl stejný) nebo když ze stejného místa vezmu daná data a chci je vypálit v K3B (verze 1.0). Při vypalování se mi to ještě nedávno projevovalo až při vypalování druhého nebo třetího DVD, ale dnes se mi to projeviolo při kopírování DVD na disk okamžitě. V obou případech se velmi vytíží systém a daná operace trvá mnohonásobně déle a hlavně, když hýbu myší, hýbe se úplně zpomaleně a když chci na něco kliknout skoro pořád uskakuje (je pak docela problém cokoliv dělat). Ve chcíli když kopírování nebo vypalování skončí, systém zas běží jak má. Přijde mi to jako nějaké špatné uvolňování paměti nebo něco takového, ale nevím na co přesně se zaměřit. Mám podezření na nějakou chybu s kio moduly (měl jsem s nimi trochu starosti už na 10.1).
Rád bych tedy poprosil zkušené Linuxáře, zda by mi nepomohli tento problém vyřešit ... klidně pošlu výpis skoro čehokoliv co by mohlo pomoci s hledáním příčiny, jen potřebuji navézt.
Děkuji moc předem za jakoukoliv pomoc.
Petr

kio tohle celkem spolehlive nezpusobi, aby zpusobilo, tak by muselo byt celkem znacne rozbite.

Spise se zamerte na to, jestli mate zapnute DMA na onech IDE zarizenich (hdparm /dev/zarizeni) a jestli se vlivem nejake chyby samo od sebe nevypne (dmesg).

Tak hdparm mi na tom zařízení ukazuje zapnutý dma:
Pro ten společný Ext3 oddíl:
hdparm /dev/hdb5

/dev/hdb5:
multcount = 16 (on)
IO_support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 38913/255/63, sectors = 421690122, start = 203447223

A pro linuxový oddíl (/):
hdparm /dev/hdb3

/dev/hdb3:
multcount = 16 (on)
IO_support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 38913/255/63, sectors = 188747685, start = 14699475


Ale ten dmesg mi na konci vrací nějaké chyby, ale moc se v tom nevyznám (nicméně u těch chyb je psáno eth0, což by měla být pokud se nemýlím síť, což by mohl být třeba jen chvilkový výpadek připojení k internetu a tudíž by to s tím problémem vůbec nemuselo souviset).
Přikládám tedy výstup z dmesg, budu moc rád, pokud mi někdo poradí:

Linux version 2.6.18.8-0.1-default (geeko@buildhost) (gcc version 4.1.2 20061115
(prerelease) (SUSE Linux)) #1 SMP Fri Mar 2 13:51:59 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fb940
On node 0 totalpages: 262128
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32752 pages, LIFO batch:7
DMI 2.3 present.
Using APIC driver default
IO/L-APIC allowed because system is MP or new enough
ACPI: RSDP (v000 AMI ) @ 0x000fa900
ACPI: RSDT (v001 AMIINT VIA_K7 0x00000010 MSFT 0x00000097) @ 0x3fff0000
ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @ 0x3fff0030
ACPI: MADT (v001 AMIINT VIA_K7 0x00000009 MSFT 0x00000097) @ 0x3fff00c0
ACPI: DSDT (v001 VIA VIA_K7 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:6 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Detected 1666.809 MHz processor.
Built 1 zonelists. Total pages: 262128
Kernel command line: root=/dev/hdb3 resume=/dev/hdb1 splash=silent
bootsplash: silent mode.
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1032132k/1048512k available (1697k kernel code, 15556k reserved, 972k da
ta, 196k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3336.74 BogoMIPS (lpj=6673480)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 0
0000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 0000000
0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
checking if image is initramfs... it is
Freeing initrd memory: 3170k freed
ACPI: Core revision 20060707
CPU0: AMD Athlon(tm) XP 2000+ stepping 02
Total of 1 processors activated (3336.74 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by vt8235 PM
PCI quirk: region 0400-040f claimed by vt8235 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: c000-cfff
MEM window: dfe00000-dfefffff
PREFETCH window: bfc00000-dfcfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1176558349.824:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:03: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
input: GenPS/2 Genius Mouse as /class/input/input2
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 1
Using IPI No-Shortcut mode
ACPI: (supports S0<6>Time: tsc clocksource has been installed.
S1 S4 S5)
Freeing unused kernel memory: 196k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: Unable to derive IRQ for device 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
PCI: VIA IRQ fixup for 0000:00:11.1, from 255 to 15
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST3160023A, ATA DISK drive
hdb: ST3320620A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 >
hdb: max request size: 512KiB
hdb: 625142448 sectors (320072 MB) w/16384KiB Cache, CHS=38913/255/63, UDMA(100)
hdb: cache flushes supported
hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 >
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP
,DMA]
lp0: using parport0 (interrupt-driven).
usbcore: registered new driver usbfs
usbcore: registered new driver hub
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.0, from 11 to 9
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 169, io base 0x0000e000
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.18.8-0.1-default uhci_hcd
usb usb1: SerialNumber: 0000:00:10.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Linux agpgart interface v0.101 (c) Dave Jones
ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.1, from 10 to 9
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 169, io base 0x0000e400
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.18.8-0.1-default uhci_hcd
usb usb2: SerialNumber: 0000:00:10.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.2, from 10 to 9
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 169, io base 0x0000e800
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.18.8-0.1-default uhci_hcd
usb usb3: SerialNumber: 0000:00:10.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.3, from 5 to 9
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 169, io mem 0xdffffe00
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: EHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.18.8-0.1-default ehci_hcd
usb usb4: SerialNumber: 0000:00:10.3
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:11.5 to 64
8139too Fast Ethernet driver 0.9.27
gameport: NS558 PnP Gameport is pnp00:05/gameport0, io 0x200, speed 864kHz
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 185
eth0: RealTek RTL8139 at 0xf8868f00, 00:08:a1:26:35:c8, IRQ 185
eth0: Identified 8139 chip type 'RTL-8139C'
NET: Registered protocol family 23
hdc: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Adding 2104472k swap on /dev/hdb1. Priority:-1 extents:1 across:2104472k
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERM
ANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 929 MBytes.
[fglrx] module loaded - fglrx 8.28.8 [Aug 17 2006] on minor 0
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
loop: loaded (max 8 devices)
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver 2.1.27 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs warning (device hda1): load_system_files(): Unsupported volume flags 0x4
000 encountered.
NTFS-fs warning (device hda1): load_system_files(): Volume has unsupported flags
set. Will not be able to remount read-write. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8191 buckets, 65528 max) - 228 bytes per conntrack
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU1] (supports 16 throttling states)
powernow-k8: Processor cpuid 662 not supported
audit(1176551180.257:2): audit_backlog_limit=256 old=64 by auid=4294967295
audit(1176551180.469:3): audit_pid=2822 old=0 by auid=4294967295
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 17
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=72
TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=52
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=72
TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=52
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=72
TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=52
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105
TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105
TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105
TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105
TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105
TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105
TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105
TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=81.223.20.170 LEN=52 TOS=0x00 P
REC=0x00 TTL=64 ID=65489 DF PROTO=TCP SPT=1729 DPT=80 WINDOW=54 RES=0x00 ACK FIN
URGP=0 OPT (0101080AFFFFEBAA0A711100)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=193.190.198.20 LEN=52 TOS=0x00
PREC=0x00 TTL=64 ID=59287 DF PROTO=TCP SPT=13432 DPT=80 WINDOW=54 RES=0x00 ACK F
IN URGP=0 OPT (0101080AFFFFEBBC08D64E37)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=193.233.9.194 LEN=52 TOS=0x00 P
REC=0x00 TTL=64 ID=62274 DF PROTO=TCP SPT=27248 DPT=80 WINDOW=54 RES=0x00 ACK FI
N URGP=0 OPT (0101080AFFFFEBBC38EA00E5)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.135.221.130 LEN=52 TOS=0x00
PREC=0x00 TTL=64 ID=29088 DF PROTO=TCP SPT=19216 DPT=80 WINDOW=78 RES=0x00 ACK
FIN URGP=0 OPT (0101080AFFFFEBBD1463C086)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.238.1.7 LEN=52 TOS=0x00 PRE
C=0x00 TTL=64 ID=64183 DF PROTO=TCP SPT=13229 DPT=80 WINDOW=54 RES=0x00 ACK FIN
URGP=0 OPT (0101080AFFFFEBBD1F475AFA)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=193.233.9.194 LEN=52 TOS=0x00 P
REC=0x00 TTL=64 ID=62280 DF PROTO=TCP SPT=27248 DPT=80 WINDOW=54 RES=0x00 ACK FI
N URGP=0 OPT (0101080A0000061238EA00E5)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=193.233.9.194 LEN=52 TOS=0x00 P
REC=0x00 TTL=64 ID=62281 DF PROTO=TCP SPT=27248 DPT=80 WINDOW=54 RES=0x00 ACK FI
N URGP=0 OPT (0101080A000020D238EA00E5)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.238.1.7 LEN=52 TOS=0x00 PRE
C=0x00 TTL=64 ID=64191 DF PROTO=TCP SPT=13229 DPT=80 WINDOW=54 RES=0x00 ACK FIN
URGP=0 OPT (0101080A000026821F475AFA)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=193.233.9.194 LEN=52 TOS=0x00 P
REC=0x00 TTL=64 ID=62282 DF PROTO=TCP SPT=27248 DPT=80 WINDOW=54 RES=0x00 ACK FI
N URGP=0 OPT (0101080A0000565238EA00E5)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=212.201.44.24 LEN=52 TOS=0x00 P
REC=0x00 TTL=64 ID=30070 DF PROTO=TCP SPT=21761 DPT=80 WINDOW=1553 RES=0x00 ACK
FIN URGP=0 OPT (0101080A0000585730E4C073)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.135.221.130 LEN=52 TOS=0x00
PREC=0x00 TTL=64 ID=9850 DF PROTO=TCP SPT=15851 DPT=80 WINDOW=69 RES=0x00 ACK F
IN URGP=0 OPT (0101080A0000AD6614645150)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.135.221.130 LEN=52 TOS=0x00
PREC=0x00 TTL=64 ID=9851 DF PROTO=TCP SPT=15851 DPT=80 WINDOW=69 RES=0x00 ACK F
IN URGP=0 OPT (0101080A0000AD9F14645150)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=212.201.44.24 LEN=52 TOS=0x00 P
REC=0x00 TTL=64 ID=31600 DF PROTO=TCP SPT=1635 DPT=80 WINDOW=69 RES=0x00 ACK FIN
URGP=0 OPT (0101080A0000ADC030E7FCC5)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.135.221.130 LEN=52 TOS=0x00
PREC=0x00 TTL=64 ID=9852 DF PROTO=TCP SPT=15851 DPT=80 WINDOW=69 RES=0x00 ACK F
IN URGP=0 OPT (0101080A0000AE1114645150)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=134.109.132.91 LEN=52 TOS=0x00
PREC=0x00 TTL=64 ID=24044 DF PROTO=TCP SPT=24934 DPT=80 WINDOW=77 RES=0x00 ACK F
IN URGP=0 OPT (0101080A0000AEFF4EA91843)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.135.221.130 LEN=52 TOS=0x00
PREC=0x00 TTL=64 ID=9857 DF PROTO=TCP SPT=15851 DPT=80 WINDOW=69 RES=0x00 ACK F
IN URGP=0 OPT (0101080A0000C9AD14645150)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.135.221.130 LEN=52 TOS=0x00
PREC=0x00 TTL=64 ID=9858 DF PROTO=TCP SPT=15851 DPT=80 WINDOW=69 RES=0x00 ACK F
IN URGP=0 OPT (0101080A0000E62D14645150)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=134.109.132.91 LEN=52 TOS=0x00
PREC=0x00 TTL=64 ID=24051 DF PROTO=TCP SPT=24934 DPT=80 WINDOW=77 RES=0x00 ACK F
IN URGP=0 OPT (0101080A0000EB854EA91843)
SCSI subsystem initialized
st: Version 20050830, fixed bufsize 32768, s/g segs 256
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=212.201.44.24 LEN=52 TOS=0x00 P
REC=0x00 TTL=64 ID=31608 DF PROTO=TCP SPT=1635 DPT=80 WINDOW=69 RES=0x00 ACK FIN
URGP=0 OPT (0101080A00012D4030E7FCC5)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.135.221.130 LEN=52 TOS=0x00
PREC=0x00 TTL=64 ID=20076 DF PROTO=TCP SPT=15855 DPT=80 WINDOW=69 RES=0x00 ACK
FIN URGP=0 OPT (0101080A00015EFC14645220)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.135.221.130 LEN=52 TOS=0x00
PREC=0x00 TTL=64 ID=18230 DF PROTO=TCP SPT=15856 DPT=80 WINDOW=69 RES=0x00 ACK
FIN URGP=0 OPT (0101080A00015EFD1464523F)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.135.221.130 LEN=52 TOS=0x00
PREC=0x00 TTL=64 ID=56377 DF PROTO=TCP SPT=15857 DPT=80 WINDOW=69 RES=0x00 ACK FIN URGP=0 OPT (0101080A00015EFE14645266)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.238.1.7 LEN=52 TOS=0x00 PRE C=0x00 TTL=64 ID=54604 DF PROTO=TCP SPT=20491 DPT=80 WINDOW=54 RES=0x00 ACK FIN URGP=0 OPT (0101080A00015EFF1F4795AB)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.135.221.130 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=2458 DF PROTO=TCP SPT=15858 DPT=80 WINDOW=68 RES=0x00 ACK F IN URGP=0 OPT (0101080A00015EFF146455B3)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.135.221.130 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=20083 DF PROTO=TCP SPT=15855 DPT=80 WINDOW=69 RES=0x00 ACK FIN URGP=0 OPT (0101080A00017B4314645220)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.135.221.130 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=20084 DF PROTO=TCP SPT=15855 DPT=80 WINDOW=69 RES=0x00 ACK FIN URGP=0 OPT (0101080A000197C314645220)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=195.238.1.7 LEN=52 TOS=0x00 PRE C=0x00 TTL=64 ID=54612 DF PROTO=TCP SPT=20491 DPT=80 WINDOW=54 RES=0x00 ACK FIN URGP=0 OPT (0101080A000199C41F4795AB)
SFW2-INext-DROP-DEFLT-INV IN=eth0 OUT= MAC=00:08:a1:26:35:c8:00:a0:c5:db:f4:89:0 8:00 SRC=134.109.132.91 DST=192.168.1.33 LEN=40 TOS=0x00 PREC=0x00 TTL=254 ID=65 259 PROTO=TCP SPT=80 DPT=24952 WINDOW=54 RES=0x00 RST URGP=0
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=134.109.132.91 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=8607 DF PROTO=TCP SPT=24952 DPT=80 WINDOW=54 RES=0x00 ACK FI N URGP=0 OPT (0101080A0001E1EB4EAAF078)

Teď jsem si zkusil ještě hdparm na tom zařízení, kde mám tu dvd vypalovačku, při jejímž čtení a zápisu se mi to projevuje a tam mi to nějakou chybu napsalo :

hdparm /dev/hdc

/dev/hdc:
IO_support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
HDIO_GETGEO failed: Inappropriate ioctl for device



Něco jsem k tomu našel v angličtině na google, ale má angličtina není moc dobrá a i tak tomu příliš nerozumím :-(.

Ze ATAPI zarizeni nema geometrii je celkem predpokladatelne, takze to neni zajimava chyba

Nicmene podstatne je, jestli ty vypisy jsou ze stavu predtim, nez to zacne blbnout nebo az potom.

Tak ty výpisy byly v době, kdy to fungovalo dobře, zkusil jsem tedy dnes ještě udělat to samé když to blbne. Nicméně jsem dnes zkopíroval na disk asi 5 DVD než to začlo blbnout (včera hned při prvním). Když to blblo, bylo už podle hdparm vypnuté dma na té DVD mechanice:

hdparm /dev/hdc

/dev/hdc:
IO_support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 0 (off)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
HDIO_GETGEO failed: Inappropriate ioctl for device


a dmesg vyjel spoustu chyb:

Linux version 2.6.18.8-0.1-default (geeko@buildhost) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #1 SMP Fri Mar 2 13:51:59 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fb940
On node 0 totalpages: 262128
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32752 pages, LIFO batch:7
DMI 2.3 present.
Using APIC driver default
IO/L-APIC allowed because system is MP or new enough
ACPI: RSDP (v000 AMI ) @ 0x000fa900
ACPI: RSDT (v001 AMIINT VIA_K7 0x00000010 MSFT 0x00000097) @ 0x3fff0000
ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @ 0x3fff0030
ACPI: MADT (v001 AMIINT VIA_K7 0x00000009 MSFT 0x00000097) @ 0x3fff00c0
ACPI: DSDT (v001 VIA VIA_K7 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:6 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Detected 1666.809 MHz processor.
Built 1 zonelists. Total pages: 262128
Kernel command line: root=/dev/hdb3 resume=/dev/hdb1 splash=silent
bootsplash: silent mode.
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1032132k/1048512k available (1697k kernel code, 15556k reserved, 972k data, 196k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3336.76 BogoMIPS (lpj=6673523)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
checking if image is initramfs... it is
Freeing initrd memory: 3170k freed
ACPI: Core revision 20060707
CPU0: AMD Athlon(tm) XP 2000+ stepping 02
Total of 1 processors activated (3336.76 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by vt8235 PM
PCI quirk: region 0400-040f claimed by vt8235 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: c000-cfff
MEM window: dfe00000-dfefffff
PREFETCH window: bfc00000-dfcfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1176620639.824:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:03: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
input: GenPS/2 Genius Mouse as /class/input/input2
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 1
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 196k freed
Time: tsc clocksource has been installed.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: Unable to derive IRQ for device 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
PCI: VIA IRQ fixup for 0000:00:11.1, from 255 to 15
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST3160023A, ATA DISK drive
hdb: ST3320620A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 >
hdb: max request size: 512KiB
hdb: 625142448 sectors (320072 MB) w/16384KiB Cache, CHS=38913/255/63, UDMA(100)
hdb: cache flushes supported
hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 >
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Linux agpgart interface v0.101 (c) Dave Jones
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.0, from 11 to 9
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 169, io base 0x0000e000
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.18.8-0.1-default uhci_hcd
usb usb1: SerialNumber: 0000:00:10.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
8139too Fast Ethernet driver 0.9.27
NET: Registered protocol family 23
ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.1, from 10 to 9
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 169, io base 0x0000e400
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.18.8-0.1-default uhci_hcd
usb usb2: SerialNumber: 0000:00:10.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.2, from 10 to 9
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 169, io base 0x0000e800
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.18.8-0.1-default uhci_hcd
usb usb3: SerialNumber: 0000:00:10.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 177
eth0: RealTek RTL8139 at 0xf8806f00, 00:08:a1:26:35:c8, IRQ 177
eth0: Identified 8139 chip type 'RTL-8139C'
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.3, from 5 to 9
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 169, io mem 0xdffffe00
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: EHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.18.8-0.1-default ehci_hcd
usb usb4: SerialNumber: 0000:00:10.3
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:11.5 to 64
gameport: NS558 PnP Gameport is pnp00:05/gameport0, io 0x200, speed 864kHz
hdc: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Adding 2104472k swap on /dev/hdb1. Priority:-1 extents:1 across:2104472k
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 929 MBytes.
[fglrx] module loaded - fglrx 8.28.8 [Aug 17 2006] on minor 0
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
loop: loaded (max 8 devices)
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver 2.1.27 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs warning (device hda1): load_system_files(): Unsupported volume flags 0x4000 encountered.
NTFS-fs warning (device hda1): load_system_files(): Volume has unsupported flags set. Will not be able to remount read-write. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8191 buckets, 65528 max) - 228 bytes per conntrack
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU1] (supports 16 throttling states)
powernow-k8: Processor cpuid 662 not supported
audit(1176613471.921:2): audit_pid=2813 old=0 by auid=4294967295
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 17
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=72 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=52
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=72 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=52
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=72 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=52
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.33 DST=224.0.0.251 LEN=105 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=85
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=88.86.100.53 LEN=723 TOS=0x00 PREC=0x00 TTL=64 ID=39344 DF PROTO=TCP SPT=3697 DPT=80 WINDOW=298 RES=0x00 ACK PSH FIN URGP=0 OPT (0101080A0002DE320AC4A2F7)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=192.168.1.33 DST=88.86.100.53 LEN=723 TOS=0x00 PREC=0x00 TTL=64 ID=39345 DF PROTO=TCP SPT=3697 DPT=80 WINDOW=298 RES=0x00 ACK PSH FIN URGP=0 OPT (0101080A0002FB320AC4A2F7)
usb 4-3: new high speed USB device using ehci_hcd and address 2
usb 4-3: new device found, idVendor=04a9, idProduct=10a2
usb 4-3: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-3: Product: iP4200
usb 4-3: Manufacturer: Canon
usb 4-3: SerialNumber: C181C5
usb 4-3: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04A9 pid 0x10A2
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
hdc: media error (blank): status=0x51 { DriveReady SeekComplete Error }
hdc: media error (blank): error=0x84 { AbortedCommand LastFailedSense=0x08 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Blank check -- (Sense key=0x08)
(vendor-specific error) -- (asc=0xab, ascq=0x80)
The failed "Read 10" packet command was:
"28 00 00 1f b1 d0 00 00 40 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 8308544
Buffer I/O error on device hdc, logical block 2077136
Buffer I/O error on device hdc, logical block 2077137
Buffer I/O error on device hdc, logical block 2077138
Buffer I/O error on device hdc, logical block 2077139
Buffer I/O error on device hdc, logical block 2077140
Buffer I/O error on device hdc, logical block 2077141
Buffer I/O error on device hdc, logical block 2077142
Buffer I/O error on device hdc, logical block 2077143
Buffer I/O error on device hdc, logical block 2077144
Buffer I/O error on device hdc, logical block 2077145
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 08 24 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 8336
printk: 54 messages suppressed.
Buffer I/O error on device hdc, logical block 2084
Buffer I/O error on device hdc, logical block 2085
Buffer I/O error on device hdc, logical block 2086
Buffer I/O error on device hdc, logical block 2087
Buffer I/O error on device hdc, logical block 2088
Buffer I/O error on device hdc, logical block 2089
Buffer I/O error on device hdc, logical block 2090
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 08 24 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 8336
Buffer I/O error on device hdc, logical block 2084
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 05 c3 a5 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 1511060
Buffer I/O error on device hdc, logical block 377765
Buffer I/O error on device hdc, logical block 377766
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 05 c3 a5 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 1511060
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 0a ed db 00 00 05 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 2865004
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 0a ed db 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 2865004
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 0a ed e1 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 2865028
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 0a ed e1 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 2865028
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 0f 9e ec 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 4094896
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 0f 9e ec 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 4094896
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 15 17 3a 00 00 05 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5528808
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 15 17 3a 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5528808
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 15 17 40 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5528832
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 15 17 40 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5528832
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 16 36 fc 00 00 05 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5823472
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 16 36 fc 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5823472
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 16 37 02 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5823496
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 16 37 02 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5823496
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 1e 36 2d 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 7919796
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 1e 36 2d 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 7919796
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 26 36 0d 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 10016820
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 26 36 0d 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 10016820
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 2e 35 e3 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 12113804
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 2e 35 e3 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 12113804
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 36 35 34 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 14210256
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 36 35 34 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 14210256
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 08 2b 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 8364
printk: 88 messages suppressed.
Buffer I/O error on device hdc, logical block 2091
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 08 24 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 8336
Buffer I/O error on device hdc, logical block 2084
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 08 2c 00 00 17 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 8368
Buffer I/O error on device hdc, logical block 2092
Buffer I/O error on device hdc, logical block 2093
Buffer I/O error on device hdc, logical block 2094
Buffer I/O error on device hdc, logical block 2095
Buffer I/O error on device hdc, logical block 2096
Buffer I/O error on device hdc, logical block 2097
Buffer I/O error on device hdc, logical block 2098
Buffer I/O error on device hdc, logical block 2099
hdc: irq timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hdc: DMA disabled
hdc: ATAPI reset complete
cdrom: This disc doesn't have any tracks I recognize!
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 08 24 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 8336
printk: 15 messages suppressed.
Buffer I/O error on device hdc, logical block 2084
Buffer I/O error on device hdc, logical block 2085
Buffer I/O error on device hdc, logical block 2086
Buffer I/O error on device hdc, logical block 2087
Buffer I/O error on device hdc, logical block 2088
Buffer I/O error on device hdc, logical block 2089
Buffer I/O error on device hdc, logical block 2090
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 08 24 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 8336
Buffer I/O error on device hdc, logical block 2084
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 05 c3 a5 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 1511060
Buffer I/O error on device hdc, logical block 377765
Buffer I/O error on device hdc, logical block 377766
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 05 c3 a5 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 1511060
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 0a ed db 00 00 05 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 2865004
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 0a ed db 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 2865004
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 0a ed e1 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 2865028
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 0a ed e1 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 2865028
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 0f 9e ec 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 4094896
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 0f 9e ec 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 4094896
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 15 17 3a 00 00 05 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5528808
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 15 17 3a 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5528808
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 15 17 40 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5528832
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 15 17 40 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5528832
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 16 36 fc 00 00 05 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5823472
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 16 36 fc 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5823472
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 16 37 02 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5823496
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 16 37 02 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 5823496
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 1e 36 2d 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 7919796
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 1e 36 2d 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 7919796
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 26 36 0d 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 10016820
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 26 36 0d 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 10016820
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 2e 35 e3 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 12113804
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 2e 35 e3 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 12113804
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 36 35 34 00 00 07 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 14210256
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 36 35 34 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 14210256
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 08 24 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 8336
printk: 88 messages suppressed.
Buffer I/O error on device hdc, logical block 2084
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)
The failed "Read 10" packet command was:
"28 00 00 00 08 2b 00 00 18 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 8364
Buffer I/O error on device hdc, logical block 2091
hdc: irq timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hdc: ATAPI reset complete


Osobně mi to přijde jako když nemůže správně přečíst nějaké části toho DVD, ale nevím, divné je, že se to stává dost často a při vypalování i dost brzy (většinou tak při druhém vypalovaném médiu) a navíc na Windows s tím žádnej problém nemám (ovšem to, že Windows nezobrazí chybu nemusí ještě znamenat, že tam chyba není).

Ze je bez DMA pristup strasne pomaly (a pro vypalovani prilis pomaly) je doufam pochopitelne.

To DMA se vypne tim, ze dojde k nejake chybe ukazujici na to, ze je prilis rychle. V tomto pripade to vypada tak, ze provadite nepodporovano (a do znacne miry zcestnou) operaci, ktera vyvolava chyb hromady a diky tomu mechaniku zpomalite natolik, ze prestane stihat odpovidat na prikazy dostatecne rychle.

Zaver je: nesnazte se kopirovat CSS chranene DVD 1:1 a radeji pouzijte nejaky k tomu urceny nastroj.

DVD, které jsem kopíroval nebylo nijak chráněné, bylo to vypálené DVD.

"Read of scrambled sector without authentication -- (asc=0x6f, ascq=0x03)" ukazuje na neco jineho.

Tak v tom pripade hledejte problem v hardware (spatny kabel, znecistene konektory...).

Zkusím tedy "profouknout" konektory, vyměním kabel a uvidíme. Každopádně děkuji moc za radu.