ARCHIV

Chcem naistalovat graf. ovladac pre TNT2. aby to islo tak musi byt rovnake cislo kernel(2.6.8.1-12mdk) a kernel-source(2.6-2.6.8.1-24mdk). co v mojom pripade neplati .Naistaloval som balicek kernel-2.6.8.1-24mdk cez nastaveni/baliskovac/instalovat software. Po restartu som dal overit verziu jadra a stale bola povodna. ako man postupovat aby naskocila nova jadra verzia?

Rekl bych, ze bude potreba nastavit spravne zavadec (lilo nebo grub).

1.Problem bol v tom ze som sa nemal iba odhlasit ale restartovat pocitac. Potom sa mi tam ponukla moznost spusti Linux pod novym jadrom.
2.Pri samotnej instalacii ovladaca mi vypise:
Warning:Your kernel was configured to include rivafb support as a loadable kernel module
The rivafb driver conflicts with the NVIDIA driver , the NVIDIA kernel module will still be buil
and installed, but be aware that the NVIDIA driver will not be able to function properly if the rivafb module is loaded!
Dam OK a dalej vypise :
ERROR:unable to build the NVIDIA kernel module

instaloval som ovladac :NVIDIA-Linux-x86-1.0-6111-pkg1.run
Kde by mohol byt problem?

To varovani neni problem, jenom je dobre vedet, ze modul rivafb se nesmi zavadet.

Ten ERROR je prilis obecny, mrkni se, co to zpusbouje. Installer vytvari nejaky log, treba to bude v nem.

1.ked som prepisal subor XF86Config "nv" na "nvidia"
tak mi neslo spustit graf. prostredie.
2.Neviem co jevv tom subore dolezite tak ti ho dam cely.
vidia-installer log file '/var/log/nvidia-installer.log'
creation time: Sun Jun 26 18:19:24 2005

option status:
license pre-accepted : false
update : false
force update : false
expert : false
uninstall : false
driver info : false
no precompiled interface: false
no ncurses color : false
query latest driver ver : false
OpenGL header files : false
no questions : false
silent : false
X install prefix : /usr/X11R6
OpenGL install prefix : /usr
Installer install prefix: /usr
kernel source path : (not specified)
kernel install path : (not specified)
proc mount point : /proc
ui : (not specified)
tmpdir : /root/tmp
ftp site : ftp://download.nvidia.com

Using: nvidia-installer ncurses user interface
-> License accepted.
-> No precompiled kernel interface was found to match your kernel; would you li
ke the installer to attempt to download a kernel interface for your kernel f
rom the NVIDIA ftp site (ftp://download.nvidia.com)? (Answer: Yes)
-> No matching precompiled kernel interface was found on the NVIDIA ftp site;
this means that the installer will need to compile a kernel interface for
your kernel.
-> Kernel source path: '/lib/modules/2.6.8.1-24mdk/build'
-> Performing cc_version_check with CC="cc".
-> Performing rivafb check.
-> Performing rivafb module check.
WARNING: Your kernel was configured to include rivafb support as
a loadable kernel module.

The rivafb driver conflicts with the NVIDIA driver; the
NVIDIA kernel module will still be built and installed,
but be aware that the NVIDIA driver will not be able to
function properly if the rivafb module is loaded!
-> Cleaning kernel module build directory.
executing: 'cd ./usr/src/nv; make clean'...
rm -f -f nv.o os-agp.o os-interface.o os-registry.o nv.o os-agp.o os-interfa
ce.o os-registry.o nvidia.mod.o
rm -f -f build-in.o nv-linux.o *.d .*.{cmd,flags}
rm -f -f nvidia.{o,ko,mod.{o,c}} nv_compiler.h *~
-> Building kernel module:
executing: 'cd ./usr/src/nv; make module SYSSRC=/lib/modules/2.6.8.1-24mdk/b
uild SYSOUT=/lib/modules/2.6.8.1-24mdk/build'...
Your kernel was configured to include rivafb support as
a loadable kernel module.

The rivafb driver conflicts with the NVIDIA driver; the
NVIDIA kernel module will still be built and installed,
but be aware that the NVIDIA driver will not be able to
function properly if the rivafb module is loaded!

*** Failed rivafb module sanity check, but continuing! ***


NVIDIA: calling KBUILD...
make -C /lib/modules/2.6.8.1-24mdk/build \
KBUILD_SRC=/usr/src/linux-2.6.8.1-24mdk KBUILD_VERBOSE=1 \
KBUILD_CHECK= KBUILD_EXTMOD="/root/tmp/selfgz7865/NVIDIA-Linux-x86-1.0-6111-
pkg1/usr/src/nv" \
-f /usr/src/linux-2.6.8.1-24mdk/Makefile modules
mkdir -p /root/tmp/selfgz7865/NVIDIA-Linux-x86-1.0-6111-pkg1/usr/src/nv/.tmp
_versions
make -f /usr/src/linux-2.6.8.1-24mdk/scripts/Makefile.build obj=/root/tmp/se
lfgz7865/NVIDIA-Linux-x86-1.0-6111-pkg1/usr/src/nv
echo \#define NV_COMPILER \"`cc -v 2>&1 | tail -n 1`\" > /root/tmp/selfgz786
5/NVIDIA-Linux-x86-1.0-6111-pkg1/usr/src/nv/nv_compiler.h
cc -Wp,-MD,/root/tmp/selfgz7865/NVIDIA-Linux-x86-1.0-6111-pkg1/usr/src/nv/
.nv.o.d -nostdinc -iwithprefix include -D__KERNEL__ -Iinclude -Iinclude2 -I/
usr/src/linux-2.6.8.1-24mdk/include -I/root/tmp/selfgz7865/NVIDIA-Linux-x86
-1.0-6111-pkg1/usr/src/nv -Wall -Wstrict-prototypes -Wno-trigraphs -fno-stri
ct-aliasing -fno-common -pipe -msoft-float -mpreferred-stack-boundary=2 -fno
-unit-at-a-time -march=i686 -I/usr/src/linux-2.6.8.1-24mdk/include/asm-i386/
mach-default -Iinclude/asm-i386/mach-default -O2 -Wdeclaration-after-stateme
nt -I/root/tmp/selfgz7865/NVIDIA-Linux-x86-1.0-6111-pkg1/usr/src/nv -Wall -
Wimplicit -Wreturn-type -Wswitch -Wformat -Wchar-subscripts -Wparentheses -W
pointer-arith -Wno-multichar -Werror -O -fno-common -MD -Wno-cast-qual -Wno-
error -D_LOOSE_KERNEL_NAMES -D__KERNEL__ -DMODULE -DNTRM -D_GNU_SOURCE -D_LO
OSE_KERNEL_NAMES -D__KERNEL__ -DMODULE -DNV_MAJOR_VERSION=1 -DNV_MINOR_VERSI
ON=0 -DNV_PATCHLEVEL=6111 -DNV_UNIX -DNV_LINUX -DNV_INT64_OK -DNVCPU_X86 -UD
EBUG -U_DEBUG -DNDEBUG -DNV_CHANGE_PAGE_ATTR_PRESENT -DNV_CLASS
_SIMPLE_PRESENT -DMODULE -DKBUILD_BASENAME=nv -DKBUILD_MODNAME=nvidia -c -o
/root/tmp/selfgz7865/NVIDIA-Linux-x86-1.0-6111-pkg1/usr/src/nv/nv.o /root/tm
p/selfgz7865/NVIDIA-Linux-x86-1.0-6111-pkg1/usr/src/nv/nv.c
/root/tmp/selfgz7865/NVIDIA-Linux-x86-1.0-6111-pkg1/usr/src/nv/nv.c: In func
tion `nv_acpi_event':
/root/tmp/selfgz7865/NVIDIA-Linux-x86-1.0-6111-pkg1/usr/src/nv/nv.c:3697: er
ror: `PM_SAVE_STATE' undeclared (first use in this function)
/root/tmp/selfgz7865/NVIDIA-Linux-x86-1.0-6111-pkg1/usr/src/nv/nv.c:3697: er
ror: (Each undeclared identifier is reported only once
/root/tmp/selfgz7865/NVIDIA-Linux-x86-1.0-6111-pkg1/usr/src/nv/nv.c:3697: er
ror: for each function it appears in.)
make[4]: *** [/root/tmp/selfgz7865/NVIDIA-Linux-x86-1.0-6111-pkg1/usr/src/nv
/nv.o] Error 1
make[3]: *** [_module_/root/tmp/selfgz7865/NVIDIA-Linux-x86-1.0-6111-pkg1/us
r/src/nv] Error 2
make[2]: *** [modules] Error 2
NVIDIA: left KBUILD.
nvidia.ko failed to build!
make[1]: *** [module] Error 1
make: *** [module] Error 2
-> Error.
ERROR: Unable to build the NVIDIA kernel module.
ERROR: Installation has failed. Please see the file
'/var/log/nvidia-installer.log' for details. You may find suggestions
on fixing installation problems in the README available on the Linux
driver download page at www.nvidia.com.

ked som prepisal subor XF86Config "nv" na "nvidia" tak mi neslo spustit graf. prostredie.

Kdo by to byl cekal :), pokud bys mel ten modul uz hotovy, tak by asi nebylo nutne ho vyrabet, coz?

Z toho vystupu se zda, ze doslo k nejake chybe pri kompilaci. Pro vsechny pripady zatim doporucuji stazeni aktualni verze a otestovani, jestli se to bude chovat stejne.

po naistalovani aktualnej verzie sa vypisalo:
Error: Unable to load the kernel module nvidia.ko. This is most likely beacuse the kernel module was built using the wrong kernel source files.Please make sure you have installed the kernel source files for your kernel, on Red Hat Linux system, for example source files are installed you may specify the kernel source path with the --kernel-source-path commandline option.

1.instaloval som to prikazom ./{instalacka} -k $(uname -r) a islo to pohode.(ziadnu chybu to nevypisalo)
2.Pri upravovani suboru XF86config som postupoval podla navodu na strankach www.abclinux.cz a http://linux.tosovsky.info/exec.php .Po spusteni Xserveru
to vypisalo ze nieje dobre nakonfigurovany.(takze to neslo)

Ta Vladova rada ohledne precteni REAME, ktere je prilozene k ovladacum a je take dostupne online rozhodne nebyla od veci, prave treba nastaveni XServeru tam je popsano.

BTW: oznamit, ze to nejde nam nepomuze, nutne je pridat alespon nejakou chybuvou hlasku apod.

Nepouzivejte pocestene prevzate a NEUPLNE navody. Prectete si dokumentaci co je prilozena k ovladacum.

V tech navodech od tech lidi co jste uvedl se vubec neresi napriklad pristupova prava - na to jiste take narazite.

Zkousel jste rucne nahrat ten modul pro NVIDII?

modprobe nvidia

Zavedl se uspesne? Taky si vyhodte (zakomentujte) polozku GLcore a dri v XF86config ci xorg.conf.

Zkuste spustit X server rucne (z virtualni konzole - klidne jako obycejny uzivatel) pomoci prikazu startx a sledujte jeho vypisy. Pripadnou chybu sem poslete a nekdo vam jiste poradi.

A rada na zaver: dokumetace v Linuxu neni pro paradu, ale vetsinou obsahuje podrobne popsane instalacni kroky vcetne FAQ a reseni problemu - to by mela byt prvni vec po ktere sahnete a druha vec pokud prvni selze by melo byt diskuzni forum s vhodne formulovanym dotazem a popsanym postupem a duvodem proc dana vec selhala.

1.Ja som si tu dokumentaciu precital este skorej ako mi to bolo povedane. S mojou slabou anglistinou som dospel k zaveru ze treba prepisat subor XFree86(co som spravil):
emove the line:
Driver "nv"
(or Driver "vesa")
(or Driver "fbdev")
and replace it with the line:
Driver "nvidia"
Remove the following lines:
Load "dri"
Load "GLCore"
In the "Module" section of the file, add the line (if it does not already
exist):
Load "glx"
2.po zadani prikazu startx vypisalo:
Release Date: 18 december 2003
X Protocol version 11, Revision 0, Relesa 6.7
Built operating System: Linux hitman 2.6.8.1-24mdk #1 Fri Jan 14
Built date:28 april 2005
Before reporting problems check http://wiki.X.org
to make sure that you have the later version
Module Loader present
Markers: (--)probed,(**)from config file,(==) default setting,(++)from command line,(!!) notice,(II)informational, (ww) warning,(EE)error,(NI)not implemented,(??) unknown.
(==)log file:"/var/log/Xorg.0.log".
(==)using config file:"/etc/X11/Xorg.conf" parse error on line 27 of section Module in file /etc/X11/Xorg.conf
"3" is not a valid keyword in this section,(EE)problem parsing the config file,(EE) Error parsing the config file
Fatal server error:
Please also check the log file at "/var/log/Xorg,0.log"
for additional
3. Zkousel jste rucne nahrat ten modul pro NVIDII?
Ako to mam urobit.
4.Ja viem ze existuje dokumentacia na internete. Problem je vtom ze je to po anglicky.

Staci si ten vystup jenom precist, na radku 27 v souboru /etc/X11/Xorg.conf je chyba, takze proto to zrejne nestartuje.

Anglictinu jsme tady tusim uz jednou resili, v IT (a nejen tam) je to proste lingua franca, takze s tim se asi neda nic moc delat a proste se alespon nejake zaklady naucit :).

3. Zkousel jste rucne nahrat ten modul pro NVIDII?

Ako to mam urobit.

Takto:

mimochodem v tom prispevku od o.k je to napsane..

1. chyba na 27 riaku je kde?
26 Load "freetype"
???? 27 Load "glx" #3D layer ????
28 EndSection
29
30 Section "InputDevice"
31 Identifier "Keyboard1"
32 Driver "keyboard"


2.pozadani modprobenvidia vypise:
FATAL: Module nvidia not found.

chyba na 27 riaku je kde?

Nu, v logu je tvrzeno toto: "(==)using config file:"/etc/X11/Xorg.conf" parse error on line 27 of section Module in file /etc/X11/Xorg.conf "3" is not a valid keyword in this section,(EE)problem parsing the config file,(EE) Error parsing the config file". I kdyz se mi "Load "glx" #3D layer" zda naprosto korektni, tak doporucuju smazat komentar (# a vse za nim) a pokud se bude chyba opakovat, opet posli vystup.

pozadani modprobenvidia vypise: FATAL: Module nvidia not found.

To nevypada moc dobre, modul nvidia mel byt prave vyslekem kompilace. Pokud nepomuze neco jako depmod -a, bude asi potrebe vratit se znovu na zacatek :|.

Vzdyt to bije do oci - hodte si ten komentar

#3D layer

na novy radek a mate pro problemech s parsovanim. Ne vsechny konfiguracni soubory akceptuji komentar za volbou - na to pozor.

Druha vec - ten modul se vam zjevne nevybuildoval nebo se vybuildoval pro jinou verzi jadra.

1.ak som dal #3D layer na novy riadok tak po zadani prikazu
startx vypisal chybu:
Module Loader present
Markers: (--)probed,(**)from config file,(==) default setting,(++)from command line,(!!) notice,(II)informational, (ww) warning,(EE)error,(NI)not implemented,(??) unknown.
(==)log file:"/var/log/Xorg.0.log".
(==)using config file:"/etc/X11/Xorg.conf"
(EE)NO device detected
(ale uz nevypisalo uchybu na 27 riadku)
2.po zadani prikazu depmod -a sa vypisalo:
bash: depmod: command not found
3. Ako zistim ze sa mi vybuildoval modul?
Ak zistim ze sa mi vybuildoval pro jinou verzi jadra?
A ako vybuildujem ten modul pre dane jadro?

(EE)NO device detected

Stalo se to, co bylo predpovidano -- zrejme se nevybuildoval modul pro nvidii ... takze se budes muset vratit znovu na zacatek.

bash: depmod: command not found

Neverim :), urcite to bylo spustene rootem?

Ako zistim ze sa mi vybuildoval modul?

Pokud po zadani prikazu modprobe nvidia nezarve zadny FATAL a modul bude v seznamu modulu (viz lsmod).

Ak zistim ze sa mi vybuildoval pro jinou verzi jadra?

Typicky tak, ze nekde v /lib/modules/{uname -r} najdes nvidia.ko.

A ako vybuildujem ten modul pre dane jadro?

Nejlepe asi tak, ze do nej rebootujes, vypnes XServer a spustis NVIDIA Installer.

Mimochodem, cetl jsi si k tomu dokumentaci? Mas Mandrake? Pokud ano, cetl jsi si vybornou prirucku od Ivana Bibra, kde je zrovna tohle hezky cesky popsano?

V prirucce k Mandrakelinuxu 10.1 je to na strane 235 - predpokladam, ze v tom PDFku to bude na stejne strane.

Mozna se vam taky nevybuildoval kvuli tomu, ze nemate zdrojaky jadra - takze:

urpmi kernel-source

1.v prirucke je pisane(str.237) ERROR:....
Instalacny program nenasiel zdrojovy kod jadra....
. Toto som vyriesil uplene na zaciatku (vid. 1 dotaz)
PRECO potom vypisuje stale ERROR?
Aj som preinstaloval jadro 2.6.8.1-25mdk a dal tam zdrojovy kod jadra 2.6-2.6.8.1-25mdk. Po instalacii som dal overit verziu kernel-source a bola naistalovana.
2.preco sa nevytvotil modul nvidia?ked som pozil prikaz ./{instalacka} -k $(uname -r) (sice ziadnu chybu nevypisalo ) a ked som pouzil prikaz ./{instalacka} (vypisalo ERROR)
3.po zadani prikazu (ako root) depmod -a sa nevypisalo
nic a naskocil novy riadok (# )
4.chybova hlaska pre subor nvidia-installer.log.:


VIDIA: left KBUILD.
-> done.
-> Kernel module compilation complete.
ERROR: Unable to load the kernel module 'nvidia.ko'. This is most likely
because the kernel module was built using the wrong kernel source files.
Please make sure you have installed the kernel source files for your
kernel; on Red Hat Linux systems, for example, be sure you have the
'kernel-source' rpm installed. If you know the correct kernel source
files are installed, you may specify the kernel source path with the
'--kernel-source-path' commandline option.
-> Kernel module load error: insmod: error inserting './usr/src/nv/nvidia.ko':
-1 No such device
-> Kernel messages:
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10377
bytes, v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10377
bytes, v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture.... found (800x600, 10377
bytes, v3).
bootsplash: status on console 5 changed to on
Shorewall:net2all:DROP:IN=eth0 OUT= MAC= SRC=10.100.100.98
DST=10.100.100.255 LEN=139 TOS=0x00 PREC=0x00 TTL=64 ID=327 DF PROTO=UDP
SPT=631 DPT=631 LEN=119
nvidia: module license 'NVIDIA' taints kernel.
NVRM: The NVIDIA RIVA TNT2/TNT2 Pro GPU installed in this system is
NVRM: supported through the NVIDIA Legacy drivers. Please
NVRM: visit http://www.nvidia.com/object/unix.html for more
NVRM: information. The 1.0-7667 NVIDIA driver will ignore
NVRM: this GPU. Continuing probe...
NVRM: No NVIDIA graphics adapter found!
Shorewall:net2all:DROP:IN=eth0 OUT= MAC= SRC=10.100.100.98
DST=10.100.100.255 LEN=139 TOS=0x00 PREC=0x00 TTL=64 ID=328 DF PROTO=UDP
SPT=631 DPT=631 LEN=119
ERROR: Installation has failed. Please see the file
'/var/log/nvidia-installer.log' for details. You may find suggestions
on fixing installation problems in the README available on the Linux
driver download page at www.nvidia.com.

Toto som vyriesil uplene na zaciatku (vid. 1 dotaz)
[...]
ERROR: Unable to load the kernel module 'nvidia.ko'. This is most likely because the kernel module was built using the wrong kernel source files.

No asi ne, installer si zrejme stezuje na spatne zdrojaky.

preco sa nevytvotil modul nvidia?

Protoze je vysledkem cele te kompilace, coz bys ale mel z README a doporucene dokumentace zrejme vedet.

po zadani prikazu (ako root) depmod -a sa nevypisalo nic a naskocil novy riadok (# )

Ano, to je vlastnost. Nicmene to rozhodne nema zadny smysl do doby, nez uspesne zkompilujes zaveditelny modul nvidia(.ko).

Konecne ta spravna rada. Islo to na prvy krat.
Vdaka.

To neni univerzalni, je to postup pouze pro stare karty (zrejme TNT2), takze asi delate neco spatne. Idealni bude projit nase cetne rady a pokud opravdu nic nezabere, tak poslat nejaky presny chybovy vystup a prikaz, ktery ho vyvolal.

Nejede nahodou konzole ve framebufferu?

Frame buffer by mel jit vypnout pridanim volby vga=normal jadru, napr. pokud pouzivate lilo tak v /etc/lilo.conf.

Mate distribucni jadro, nebo vlastnorucne kompilovane?

Pokud vim, tak binarni ovladace NVIDIA se s framebufferem stale nesnasi, takze jeho vypnuti bude myslim dobry zacatek.

Mate vybuildovany modul nvidia (modprobe nvidia ho zavadi, pak se objevi ve vystupu lsmod)? Co to vyhodilo pri kompilovani za chybu, pokud ne?