Používám Suse 10.0 a mám problém. Když chci nahrát data na svoji MP3 Xtreme 1Gb, tak mi to jede asi 80Kb přitom stahování asi 4Mb. To stejne je u fotaku Kodak Easy Share Z740. Stahování trvá hrozně dlouho. Můžete mi prosím někdo poradit jak to zrychlit?? (mám USB 2.0)

Přihoďte sem kus výstupu s dmesg a případně lsci a lsusb... Jste si jist, že všechny porty jsou USB2 a nepřipojujete na USB1? Mimochodem, foťák, který by zvládal USB2 jsem snad ještě nepotkal, proto mám čtečku, když potřebuji vytáhnout všechna data z karty.

Jinak to jak jste to napsal je tak na křišťálovou kouli...

s usb jsem si jistý, ale v linuxu jsem úplný nováček, takže nevím kde ty soubory mám sehnat

To je tim, ze ani jedno neni soubor, ale program, ktery genruje jakysi vystup.

Linux version 2.6.13-15-default (geeko@buildhost) (gcc version 4.0.2 20050901 (prerelease) (SUSE Linux)) #1 Tue Sep 13 14:56:15 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61424 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 VIA694 ) @ 0x000f7d30
ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3000
ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3040
ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: local apic disabled
Allocating PCI resources starting at 10000000 (gap: 10000000:efff0000)
Built 1 zonelists
Kernel command line: root=/dev/hdb2 vga=0x31a selinux=0 resume=/dev/hdb1 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 784.526 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 253904k/262080k available (2028k kernel code, 7564k reserved, 700k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1570.48 BogoMIPS (lpj=3140973)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000020 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: AMD Duron(tm) Processor stepping 01
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1745k freed
ACPI: Looking for DSDT in initrd... not found!
not found!
ACPI: setting ELCR to 0800 (from 0e20)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb440, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
PCI: Bridge: 0000:00:01.0
IO window: c000-cfff
MEM window: d8000000-d9ffffff
PREFETCH window: d4000000-d7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1172760382.124:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
vesafb: framebuffer at 0xd4000000, mapped to 0xd0880000, using 10240k, total 32768k
vesafb: mode is 1280x1024x16, linelength=2560, pages=11
vesafb: protected mode interface info at c000:4804
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 112645 bytes,<6>...found (1280x1024, 17839 bytes, v3).
Console: switching to colour frame buffer device 158x59
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices:
SLPB PCI0 USB0 USB1 MODM UAR1 UAR2 ECP1
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 204k freed
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
PCI: Via IRQ fixup for 0000:00:07.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
hda: WDC WD200BB-00CFC0, ATA DISK drive
hdb: QUANTUM FIREBALL CX10.2A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 39100223 sectors (20019 MB)
native capacity is 39102336 sectors (20020 MB)
hda: Host Protected Area disabled.
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1
hdb: max request size: 128KiB
hdb: 20044080 sectors (10262 MB) w/418KiB Cache, CHS=19885/16/63
hdb: cache flushes not supported
hdb:hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: DMA disabled
ide0: reset: success
hdb1 hdb2
Probing IDE interface ide1...
hdd: LITE-ON LTR-48246K, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
hdd: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
swsusp: Suspend partition has wrong signature?
ReiserFS: hdb2: found reiserfs format "3.6" with standard journal
ReiserFS: hdb2: using ordered data mode
ReiserFS: hdb2: journal params: device hdb2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb2: checking transaction log (hdb2)
ReiserFS: hdb2: Using r5 hash to sort names
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Adding 514040k swap on /dev/hdb1. Priority:-1 extents:1
bootsplash: status on console 0 changed to on
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
parport_pc: VIA parallel port: io=0x378, irq=7
lp0: using parport0 (interrupt-driven).
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart: AGP aperture is 64M @ 0xd0000000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x0000d400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.3: irq 11, io base 0x0000d800
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0b.0: irq 10, io mem 0xdb001000
8139too Fast Ethernet driver 0.9.27
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:0d.0: OHCI Host Controller
ohci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:0d.0: irq 10, io mem 0xdb002000
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xd1736000, 00:4f:4e:13:d5:2a, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:0d.1[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:0d.1: OHCI Host Controller
ohci_hcd 0000:00:0d.1: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:0d.1: irq 5, io mem 0xdb003000
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:0d.2[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:0d.2: EHCI Host Controller
ehci_hcd 0000:00:0d.2: new USB bus registered, assigned bus number 6
ehci_hcd 0000:00:0d.2: irq 10, io mem 0xdb004000
ehci_hcd 0000:00:0d.2: USB 2.0 initialized, EHCI 0.95, driver 10 Dec 2004
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 5 ports detected
bootsplash: status on console 0 changed to on
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 17
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
NET: Registered protocol family 10
Disabled Privacy Extensions on device c036b920(lo)
IPv6 over IPv4 tunneling driver
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: CPU0 not a capable Intel processor
microcode: No new microcode data for CPU0
IA-32 Microcode Update Driver v1.14 unregistered
bootsplash: status on console 0 changed to on
powernow-k8: Processor cpuid 631 not supported
powernow: No powernow capabilities detected
bootsplash: status on console 0 changed to on
eth0: no IPv6 routers present
subfs 0.9
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
subfs: unsuccessful attempt to mount media (256)
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
scsi: unknown opcode 0x01

Jeden by usoudil, ze s USB to nema vubec nic spolecneho.

Vymente ATA kabel na primarnim kanalu (pokud tam mate ten, co tam ma opravdu byt, tak ho alespon ocistete od prachu a jinych necistot), pokud to nepomuze, nastavte nizsi prenosovou rychlost ci zkuste jestli problem neni v radici ci disku.

Ohledne sekundarniho ATA kanalu bych jeste poznamenal, ze jedine zarizeni by melo mit adresu 0 (tj. master).

Toto je dlouho známý problém se špatně sestaveným jádrem. Zkuste updatovat jádro přes yast.